Manual de ProgramaciónESPECIFICACIONES SUJETAS A CAMBIO SIN PREVIO AVISO.SM2410, SM2410B, SM2420 y SM2430
3 DEFAULT VALUES OF OPERATING PARAMETERS Function Default Sleep mode Motor sleep mode After 30 minutes Laser sleep mode After 15 minutes Scanner tim
4 DEFAULT VALUES OF KEYBOARD EMULATION PARAMETERS SETTING Function Default Values Keyboard type selection IBM PC/AT USA Message terminator Enter/ ca
5 DEFAULT VALUES OF DECODING PARAMETERS Function Code Default Value Code 39 Enable ITF 2 of 5 Disable Chinese Post Code Disable UPC/EAN/JAN Enable
6 UPC-E check digit Transmit Type Standard Start/stop characters A,B,C,D Codabar Length 6~32 digits FNC 2 append Disable Code 128 Check digit Disab
7 PROGRAM PROCEDURE USING BARCODE MENUS Read Enter/Exit programming mode barcode to start of configurationChange scanner setting by scanning mode Se
8 Enter/Exit Programming Mode All framed barcode names represent as default settings.
9 SYSTEM SETTING
10 RESET ※ The reading of the “RESET” label turns all the parameters back to default values. ※ The scanner remains in the last interface mode whe
11 Save as Customer default The setting allows the multi-desired setting barcode to be saved as a customer default. The RS-232C interfa
12 Return to PC/AT default Keyboard wedge interface for IBM PC AT and compatibles Return to USB default
Enter/Exit Programming Mode (This barcode is also found at page 8.)
13 Return to customer default The reading of the “ABORT” label discards all the parameters reading prior to the “Enter/Exit of Programmi
14 SLEEP MODE
15 Motor Sleep mode off Motor Sleep after 30 minutes
16 Motor sleep after 60 minutes Laser sleep mode off
17 Laser sleep after 15 minutes Laser sleep after 30 minutes
18 BEEPER TONE
19 High Frequency Medium Frequency
20 Low Frequency Long sound duration (100msec.)
21 Medium sound duration (50msec) Short sound duration (20msec.)
22 SCANNER TIMING
IMPORTANT NOTICE Every effort is mode to ensure the accuracy of our product information; however, we accept no responsibility for errors or omissi
23 Same code delay time 200 msec. Same Code delay 300msec
24 Same code delay 500msec Same code delay time 600 msec.
25 RS-232 COMMUNICATION
26 Baud Rate 19200 Baud Rate 9600
27 Baud Rate 4800 Baud Rate 2400
28 7 Data bit 8 Data bit
29 1 Stop bit 2 Stop bit
30 Even parity Odd Parity
31 Mark parity Space Parity
32 None Parity None Handshaking
TABLE OF CONTENTS Introduction... 1 Change the scanner setting...
33 RTS/CTS on Message terminator-None
34 Message Terminator-CR/LF Message Terminator-CR
35 Message Terminator-LF Message Terminator-H.tab
36 Message Terminator-STX/ETX Message Terminator-EOT
37 KEYBOARD WEDGE
38 US Keyboard International Keyboard (ALT method)
39 Message Terminator-None Message Terminator-Enter
40 Message Terminator-H.tab
41 CAPITAL LOCK Select the suitable code to match your keyboard caps lock status Capital lock on Capital lock off
42 FUNCTION KEY EMULATION The series allow you to emulate Function keys, Arrow keys, and many other “extended” keys. An IBM compatible keyboard does
Same code delay 500msec... 24 Same code delay 600msec... 24 RS-232 communica
43 USB INTERFACE
44 US Keyboard International Keyboard (ALT method)
45 Message Terminator-Enter Message terminator-None
46 Message Terminator-H.tab
47 CODE SELECTION
48 Code 39 Enable Code 39 Disable
49 FULL ASCII CODE39 Enable FULL ASCII CODE 39 Disable
50 Codabar Enable Codabar Disable
51 UPC/EAN/JAN Enable UPC/EAN/JAN Disable
52 ITF 2 of 5 Enable ITF 2 OF 5 Disable
Message terminator-H.tab... 46 Code selection... 47
53 Chinese Post Code Enable Chinese Post Code Disable
54 Code 128 Enable Code 128 Disable
55 Code 93 Enable Code 93 Disable
56 EAN-128 Enable EAN-128 Disable
57 Code 32 Enable (Italian Pharmacy Code) Code 32 Disable (Italian Pharmacy Code)
58 MSI enable MSI Disable
59 EAN-13 Convert to ISBN/ISSN Enable EAN-13 Convert to ISBN/ISSN Disable
60 UPC/EAN ADD ON OFF ADD ON 5 only
61 ADD ON 2 only ADD ON 2 or 5
62 EAN/UPC +Add on (none mandatory) EAN/UPC + Add on ( mandatory)
Data editing... 68 Header (preamble) ...
63 Force UPC-A to EAN-13 format enable Force UPC-A to EAN-13 format disable
64 BARCODE IDENTIFIER CODE SETTING
65 The series scanner can transmit max.2 digit barcode identifier code for different type of barcode, Use enable or disable identifier setting barcod
66 BARCODE IDENTIFIER CODE SELECTION Disable identifier code scan “enable identifier code” label to transmit the label ID as following table Enable
67 SET MESSAGE FORMAT WITH CODE IDENTIFIER AS ALPHA-30 FORMAT IS02 Code Code identifier UPC-A A UPC-E E EAN-8 FF EAN-13 F CODE 39 * CODBAR % ITF 2
68 DATA EDITING
69 The Header and Trailer allows you to append a header and/or a trailer to every message transmitted via the serial ports or the keyboard port.
70 Trailer (Postamble) Set
71 CODE LENGTH SETTING FLOW Programming Minimum or Maximum label Scan “SET” label to confirm your choice into memory. Scan two nu
72 ITF 2 OF 5 Min. length setting ITF 2 of 5 Max. length setting
1 1. INTRODUCTION The series of scanners can be configured by scanning a series of programming barcode labels. This allows decoding options and int
73 Chinese post code maximum Length setting Chinese post code minimum Length setting
74 ASCII CHARACTER
75 SOH STX
76 ETX EOT
77 HT LF
78 CR ESC
79 # $
80 % *
81 0 1
82 2 3
2 2. CHANGE THE SCANNER SETTING In order to change the scanner setting, please follow the sequence below 1. Scan Enter/Exit programming mode barco
83 4 5
84 6 7
85 8 9
86 Enter/Exit Programming Mode
Commentaires sur ces manuels